![]() ![]() This will ensure you get the highest quality result from your splice.Īs a note, there are some issues that may crop up with extended lengths. Most importantly, you’ll need to use a high-quality speaker wire, like this Inst allGear Speaker Wire (on Amazon). You can splice using a few tools and hardware you may already have lying around your home. Luckily for you, performing a proper splice is easy to achieve. If it’s done poorly, however, it can lead to audio dropouts and even short circuits. If it’s done well, you really shouldn’t notice any difference in your audio playback. Splicing your speaker cables can be an incredibly effective way to extend the length of your cable runs. Yet for more “reasonable” audio enthusiasts, it really won’t matter too much. For an audiophile, splicing cables may be right out. As you can imagine, this varies widely from person to person. The issues mainly come down to what people’s opinions are on what sounds good. When it comes to splicing your speaker cables, you’re going to hear some conflicting ideas. ![]() How Does Splicing Speaker Wire Affect Overall Sound Quality? So, ready to learn about splicing? We’ve got all the information you need. Of course, you could always replace the wire with a longer one, and for extended runs, this might be the best idea. If you’re interested in adding some extra length to your setup, splicing is a great choice. Just avoid simply taping wires together, as this can be risky. The easiest method is to use a wire nut to clamp two wires together, but the most durable method is to solder them. Several methods can be performed to get the perfect splice. Properly performed splices should cause no audio problems. So what’s the truth? Are some types of speaker wires better? Is splicing a good idea and, if you do choose to splice, will it reduce the overall audio quality? Some people say one thing, others say another. Some cover plates have a matte surface that allows them to be painted.When it comes to speaker wire, there’s a lot of debate out there. This technique grounds the electrical box and improves the safety of the circuit.Īfter completing the connections and finishing the wall or ceiling surface around the box, attach the cover plate securely. The free end of the pigtail is then connected to a threaded screw opening on the metal box, using a green grounding screw. For metal electrical boxes, run a third grounding pigtail (bare copper or green insulated) to the two bare copper circuit grounding wires, using a wire connector. The bare copper circuit grounding wires should also be joined together in the box, using an approved connector. With these connectors, you simply push the bare end of the wire into a grip-fit socket on the connector. Some electricians like to wrap a loop or two of electrician's tape around the base of the wire nut and wires to help reinforce the wire connection.Īnother type of approved wire connector is the push-fit connector. There should be no bare wire exposed at the bottom of the wire nut. However you do it, the wires should be connected securely enough that they don't come free from the wire nut when you tug on them. However, some wire nut manufacturers instruct to simply hold the two parallel wires together, then twist the wire nut over the bare ends of the wires in a clockwise direction. With standard wire nuts, some electricians prefer to twist the wires together first with pliers, then screw the wire nuts over the ends of the wires. Using approved wire connectors, join together the conducting wires with similar insulation colors. Trim away the severed portion of the sheathing and paper filler with the cutting jaws on a wire stripper or with a utility knife. Lightly press the sides of the ripper together and draw the tool off the end of the cable to slice through the sheathing. Insert the cable into the hole on the cable ripper until it is about 6 inches from the end of the cable. Do not use a utility knife, as you risk cutting into the individual wires. For example, a cable labeled "12/2 w ground" contains two 12-gauge insulated conductors plus a bare copper grounding wire.įirst, expose the individual conducting wires within the tough outer plastic jacket by using a cable ripper to slice through the sheathing. Make sure that you are joining two similar cables. The cables must match in terms of wire gauge and the number of individual conductors in the cable. Modern wiring (up to 50 years old or so) will have the gauge and number of wires printed on the outer sheathing of the cable. The Spruce Home Improvement Review Board.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |